What kind of intake manifold does a Vortec engine use?

Intake Manifold, Vortec Head Design 1 Designed for 283-400-cubic-inch engines using Vortec cylinder heads P/N 12558060, P/N 19300956, P/N 19300955, P/N 19331470, or P/N 19331472 2 Has 4-bolts per side to attach it to these cylinder heads 3 Aluminum high-rise design maximizes horsepower and delivers a broad torque curve

What kind of aluminum intake manifold do I Need?

Aluminum intake will work with all Vortec cylinder heads, including P/N 12558060, P/N 19300956, P/N 19300955, P/N 19331470, or P/N 19331472 NOTE: The exhaust manifold from 1996-and-newer pickup trucks with RPO L31 350 engine, P/N 12557828, is drilled and tapped to accept an EGR tube.

What kind of intake manifold does a corvette use?

NOTE: Ports do not match Bowtie cylinder heads P/N 14044861 and P/N 12363425. NOTE: Open carburetor spacer is not recommended with use of dual-plane manifolds. Designed for all 396-502 engines with GM aluminum heads (1975 and earlier) and large oval-port iron heads NOTE: May not fit on many Corvette models.

How to replace a small block engine intake manifold?

NOTE: Replacing the ECU on MEFI 3 Ram Jet engine P/N 12495515 requires using new wire harness kit P/N 12499116, or use jumper wire P/N 88963118 to use MEFI 4 ECU as an open-loop system. Includes ECU module P/N 88962717, wire harness P/N 88961967, oxygen sensor P/N 19178918, intake air temp sensor P/N 25036751, and oxygen sensor fitting P/N 15156588

What kind of intake manifolds do GM engines use?

Chevrolet Performance intake manifolds were designed specifically for GM engines, so you know they will deliver OE performance. Dual-pattern carburetor flange is approximately 1/2″ lower than the 1970 LT1 intake, yet produces the same horsepower NOTE: Open carburetor spacer is not recommended for use with dual-plane intake manifolds.

How tall is the intake manifold on a corvette?

Designed for all 396-502 engines with GM aluminum heads (1975 and earlier) and large oval-port iron heads NOTE: May not fit on many Corvette models. Manifold height is 6″ at the rear and 4.5″ in front. Check for hood clearance before ordering. NOTE: Open carburetor spacer is not recommended with use of dual-plane manifolds.

When did Vortec intake manifolds start being used?

This manifold is primarily intended for use with Vortec heads on pre-1996 engine blocks. Blocks manufactured in 1995 or earlier have thermostat bypass passage from the block directly to the water pump.

What kind of intake manifold does a Chevy bowtie have?

Bowtie Competition Small Block Intake Manifold, 18 deg Competition $417.63 Quick View Bowtie Competition Small Block Intake Manifold, Spider Design $428.37 Quick View Bowtie Competition Small Block Valley Plate Assembly $484.90 Quick View Chevy Small Block Intake Manifold, Spider Design SB2.2 $594.07 123 Categories Crate Engines Transmissions

What kind of intake manifold does a Chevy 4.3L use?

Intake Manifold, Performer TBI, Aluminum, Natural, Throttle Body Injection Style, Chevy, GMC, V6, 4.3L, Each Part Number: EDL-3713 More Detail… Order this item and get free delivery and handling on your entire order! Offer excludes truck freight and oversize fees. Valid on orders shipped in the contiguous United States.

Where are the intake gaskets on a Chevy Vortec?

The intake gaskets on the LB4 and L35 vortec’s are very prone to going bad which results in engine leaks, overheating, stalling, etc. The intake gasket sits between the intake manifold and the cylinder head.

Can a faulty intake manifold cause engine overheating?

Apart from sealing engine vacuum, certain designs will also seal engine coolant. When the intake manifold gaskets have an issue, they can cause drivability problems and even engine overheating. Usually a faulty intake manifold gasket will produce a few symptoms that can alert the driver of a potential issue. 1.

How long does it take for Chevy Vortec intake manifold to ship?

Usually ships within 6 to 10 days. . . Only 2 left in stock – order soon. . . . . Only 7 left in stock – order soon. . Usually ships within 6 to 10 days. . Only 3 left in stock – order soon.

What kind of bolt do I need for intake manifold?

Requires the use of GM attachment bolt P/N 12550027, because the bolt has a ball design on the end that sits in the head so it will not crush the intake manifold gasket

What kind of intake manifold does a Vortec engine use?