Can a 1999 Chevy c1500 / k1500 start?

Hi, our 1999 CHEVROLET C1500/K1500 is having the same issue. After sittiing for a few hours, we have to crank it and eventually put a little gas or tarting fluid in the throttle body for our truck to start but runs and drives fine once it does start and will start right up after only sitting for about an hour or so. 205 people found this helpful.

What was the ignition module for a 1996 GMC k1500?

1996 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor). Wiring diagrams.

What kind of truck is a 96 Chevy?

– CarGurus 96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark.

Why does my 96 Chevy Express van not start?

Also had a similar issue spin and no start with a 96 Chevy Express Van with the 5.7L. This vehicles issue turned out to be a shorted pink wire in the wiring harness that runs up the passenger side of the block. The vehicle had died while driving several times and wouldn’t start. Then, finally after blowing a couple fuses, would start at all.

What kind of distributor do I need for my 1996 Chevy 1500?

I have a 1996 Chevy 1500 4×4 5.7L vortec 350. We have done all the steps stated below for installation of distributor and still can not get engine into timing, runs rough, have to keep foot in the gas to keep running. Can you help? Submitted: 11 years ago. Category: Chevy Did you turn the engine over any at all when the distributor was out?

Can a Chevy C / K 1500 run without fuel?

Also I haven’t fully checked the Spark, but the Truck run’s fine when you spray Starting fluid into the Throttle body. Any suggestions on why the truck isn’t accepting the fuel, it cranks fine, just wont run without starting fluid. these trucks have to have between 55-65psi of fuel to run.

– CarGurus 96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark.

What kind of truck is a 1998 Chevy Cheyenne?

My truck is a 1998 Chevy Cheyenne 1500, 5.0L V8, 137k miles, last tune up at 110k miles. Use valvoline oil explicitly, and change every 4k miles. I got into my truck this morning, it turned over, and then died. The gauges all activated and displayed adequate oil pressure, battery power, etc.

What to do if your Chevy 1500 won’t start?

The passlock sensor voltage reading has changed & you can relearn it to the PCM & you can start the truck again. To relearn, turn the ignition key to the on position for 3 10 minute cycles, turning the key to the off position for 5 seconds after each 10 minute learn.

Where to buy a starter for a Chevy c1500?

A quality replacement starter utilizes a 12-volt battery source to start the engine and it should rotate the engine between 85 to 150 RPMs. At AutoZone stores or online, choose from a variety of motor starters for your Chevy C1500 truck. For parts purchased online, take advantage of our Same-Day Store Pick-up.

What should I replace on my 1998 Chevy k1500?

Here is what has been replaced to try and stop this misfire: spark plugs, spark plug wires twice, distributor cap twice, rotor, ignition coil, EGR, CTS on intake manifold, coolant temp gauge sender, fuel filter, fuel pump, MAF sensor, oil change.

What does it mean when a truck won’t start?

It might be the computer, but it might be a sensor or a $10 relay. You won’t get diagnostics through the internet. I have a 1998 Chevy 2500 w/ a 5.7 that wouldn’t start even though the truck had good spark, fuel in the tank, and I could hear the pump spin up and pressurize when I turned the key.

What’s the fuel pressure on a 1998 Chevy k1500?

Here are the tests I’ve done so far fuel pressure test, fuel pressure 160psi while running, then shut off for 20 min and fuel pressure was at 155 PSI. Dry Compression test on all 8 cylinders between 150-160 psi.

What kind of engine does a Chevy 2500 have?

You won’t get diagnostics through the internet. I have a 1998 Chevy 2500 w/ a 5.7 that wouldn’t start even though the truck had good spark, fuel in the tank, and I could hear the pump spin up and pressurize when I turned the key. I stuck a fuel pressure gauge on the fuel rail port and was reading about 50 psi.

How to diagnose ignition problems with 1996 suburban?

Something which might help you diagnose the issue better is to do an old school trick on your just replaced distributor cap. This would be to generously spray the inside of the cap and the rotor with WD-40. Many people use this as a lubricant to help with stuck nuts and such.

What was the ignition module for a 1996 GMC c2500?

1996 GMC C1500, C2500, C3500 Pick Up. 1996 GMC K1500, K2500, K3500 Pick Up. All of the information you need to diagnose a misfire or a no-start problem (caused by the ignition coil, the ignition module, or the crankshaft position sensor).

Can a bad ignition coil cause a car to not start?

This article will take you step by step through the whole process of diagnosing and troubleshooting a bad ignition control module and ignition coil. The ignition control module (ICM) and ignition coil tests in this article assume that your vehicle is Cranking but NOT STARTING due to a NO SPARK Condition.

Can a GM ignition control module be used?

The ignition control module (ICM) and ignition coil tests in this article assume that your vehicle is Cranking but NOT STARTING due to a NO SPARK Condition. If you’re GM car or truck starts and runs, this article will not help you.

How to help me with a Chevy k1500 misfire?

× Help us help you. By posting the year, make, model and engine near the beginning of your help request, followed by the symptoms (no start, high idle, misfire etc.) Along with any prevalent Diagnostic Trouble Codes, aka DTCs, other forum members will be able to help you get to a solution more quickly and easily!

What does ECM read on Chevy C / K 1500?

Ecm does not look at (reading on scanner will not change) unless engine is above 1000 rpm, Then you can adjust, either by rotating distributor while running (be careful)]

What’s the fuel trim on a Chevy k1500?

With fuel trims what is of interest in the total fuel trim for each bank so taking the first results bank 1 seems to have a total fuel trim of around +23% and B2 around +8%. +23% is way above what is an acceptable fuel trim and indicates the computer is adding a huge ammount of fuel to counter a lean mixture.

Why does my 1988 GMC Sierra 1500 not start?

I’m having the same problem with my 1988 GMC 1500 I was told its the starter I’m going to replace it I guess that will determine if its the starter ornot just wwish I had a for sure wayof knowing 37 people found this helpful. Having same issue. Changed out starter two days ago. Still is a hard start. Sometimes I need starter fluid

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

What should I do if my car won’t start?

Ask an assistant to turn the ignition key to the On position, but don’t start the engine. As your assistant turns the key, listen closely through the filler neck of the fuel tank. You should hear the whirring sound of the fuel pump motor being energized for two or three seconds.

Why does my Chevy 1500 turn over twice?

Okay, it’s not the ‘passlock sensor’. I reset it by leaving it in the on position for slightly over 10 minutes, turning it off for 5 seconds, and repeating 3 times. It still turns over, and dies. It did start the second time for about 1-2 seconds instead of just one turn; maybe two rotations. This has me thinking it is the fuel pump.

Why does my GM 4.3L engine not start?

No Start Condition Basics There are three very basic components that the engine, in your GM vehicle, needs to start and they are: Air, Fuel and Spark. When your 4.3L, 5.0L or 5.7L GM vehicle cranks but does not start, it’s because one of these components is missing from the mix.

Why is the AC not working on my Chevy Silverado?

Learn if it’s a simple fix or time to seek out a trusted technician. Not your vehicle? Why Isn’t My A/C Working? What are common reasons my Chevrolet Silverado 1500 has air conditioning problems?

What causes a car to not start with no spark?

Without spark, the engine will Crank but Not Start. The ignition system of the GM vehicles covered by this article use a distributor type system. In my experience, the most common component failures, of the ignition system that cause a No Start No Spark Condition are: Distributor cap. Crank sensor.

How to troubleshoot a no start GM 4.3L pick up?

Testing a Cranks but Does Not Start condition on your GM 4.3L, 5.0L, 5.7L pick up, van or SUV is not that hard to do, if you have a solid diagnostic strategy. In this article I’ll show you the basics of testing such a problem.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

Is there a problem with my Chevy Suburban?

I’m trying to diagnose an ongoing ignition problem with a 1996 Chevy Suburban. Sometimes it won’t start, and the previous owner said this happens regularly, and every time the problem occurred, replacing the distributor cap made it work again.

What kind of engine does a 1996 Suburban LT have?

Ok, we have a 1996 Suburban Lt with a 5.7L engine. We have had a few repairs but nothing this complicated before. We are driving down the interstate and suddenly the truck dies.

What happens when the ICM fails on a GM car?

Generally, when the ICM or the ignition coil fails, your GM car or truck will Crank but NOT START. Specifically, the ignition coil will not spark.

Can a Vortec engine fit in a LS car?

Although Vortec engines are “LS” based they are NOT LS engines IMO. You can gain an inch or two by removing the plastic engine cover and cutting some of the plastic tabs on top of the Vortec intake manifold. This may be all you need for clearance and a Vortec will fit in your car.

What’s the fuel pressure on a Vortec 96?

I checked my fuel pressure and its 59-60 key on engine off and 52 at idle, jumps to 60-62 after blipping throttle. I could probably run pump longer but my fuel gauge has been all over place for years and hell maybe I will pick up a bit of performance.

What kind of fuel pump does a 96 Silverado use?

I have a 96 Silverado 1500, and it did the exact same thing. It would fire with starting fluid after a line, filter, relay and pump replacement. It turned out the pump I put in was for a 96 C1500, which has a throttle body system and the pump only produced 20-30psi. The Fuel injection in the Silverado needs 55-65psi.

Why is my Chev k1500 350 Vortec not starting?

So I went and bought a sensor installed it and forgot to reset the computer before trying to start it. It changed nothing, still the same old problem. So I decided to reset the computer by disconnecting the battery, a good 10 to 15 minutes or so. Hooked it back up and still has the same problem.

What to do if your Chevy truck won’t start?

– CarGurus.ca 96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark.

What was the year of the 1997 Chevy C2500?

The illustrations in the diagnostic manual are printer friendly! Applies to: 1997 Chevrolet C1500, C2500, C3500 Pick Up. 1997 Chevrolet K1500, K2500, K3500 Pick Up. 1997 GMC C1500, C2500, C3500 Pick Up. 1997 GMC K1500, K2500, K3500 Pick Up.

What causes a 1994 Chevy C / K 1500 to bog down?

– CarGurus 1994 Chevy C1500 5.7 bogs/backfires when I give it gas. My truck bogs down (and tries to die) when I give it gas to accelerate off of a stop. There is often a backfire or two when this happens. Pumping the gas does not help. I basically have to crawl through any intersection until it picks up a bit of speed from idle. The truck

What kind of car is a C / K 1500?

Chevrolet C/K 1500 Questions – 1994 Chevy C1500 5.7 bogs/backfires when I give it gas. – CarGurus 1994 Chevy C1500 5.7 bogs/backfires when I give it gas. My truck bogs down (and tries to die) when I give it gas to accelerate off of a stop.

What is the code for a 1996 Chevy k1500?

Have a 1996 chevy k1500 has code p0300 (random miss fire) have replace cap, rotor, wires, plus, coil unit, mass air flow Have a 1996 chevy k1500 has code p0300 (random miss fire) have replace cap, rotor, wires, plus, coil unit, mass air flow – Answered by a verified Chevy Mechanic

What’s the problem with my 99 suburban 5.7 Vortec?

I am new to this site and desperate for assistance on a 99 Suburban 5.7 Vortec. Hopefully I can leverage community experience to resolve an issue that has me absolutely baffled! I purchased this vehicle a few weeks back to pull my boat. The SUV had a seized intake valve and corresponding bent pushrod on cylinder #4.

When did my 97 Silverado sense come out?

I have had my 97 Silverado sense 2002, and have spent a lot of time under the hood, as well as doing research on these trucks and engines. I also had a 93 WT with a 4,3 L v6 for 10 years before I had this truck. There are several members here with a lot of knowledge on these trucks.

What makes a Chevy k1500 hard start stall?

Hard starts with frequent stalls till warm this past winter/spring. Fuel filter change, new distributor, no change. 13 Psi fuel pressure. Changed engine coolant temp sensor by thermostat housing. Starts good and idles good again. Loading…

Why is my Chevy Silverado 1500 not starting?

If the battery is empty shortly after charging, the alternator should therefore be checked for a defect. If the battery is OK, a defect in the starter can be the cause of a non-starting vehicle. Age-related wear or a material defect can damage the starter. This is often noticeable by a clicking sound when trying to start.

What causes a Chevy pickup to hard start?

If after you have circled the key a few time the engine starts normally then you now know for sure you have a fuel pressure leak down problem causing your hard start. If this video was helpful please help support my youtube channel by subscribing here: https://www.youtube.com/channel/UChCX…

Where is the PassLock on a Chevy c1500?

96 people found this helpful. On the 98 the passlock is a module in the column and the key switch goes inside it. There is a contact inside this module that reacts to a change in magnetic field when the key switch is turned. There are three wires that come off the top of the module.

How old is the 1996 Chevy 1500 truck?

Has a matching hard shell. Sturdy, minimum dings and dents. Very little rust Needs mechanical & AC work. Compressor is ok. My Dad bought this truck about 15 years ago. It was in great shape and he kept it that way. When he passed away, he left it to me and my sister. We’ve held onto it for sentimental reasons and it was driven very rarely.

How much is a Chevrolet C1500 engine control computer?

10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Your C1500 is no stranger to hard work and neither are you. Get the most out of your truck by working smarter, not harder. Install a new Chevrolet C1500 engine control module to ensure that your engine is performing to the best of its ability.

Is the 1992 Chevy 1500 a good truck?

Showing 3 of 1,654 reviews. Comfortable to drive any distance. Some paint fade on shell and truck. Dent on lower Although 1995 this truck has been well maintained and is very reliable. Has a matching hard shell. Sturdy, minimum dings and dents. Very little rust Needs mechanical & AC work. Compressor is ok.

Where did the 1996 Chevy C / K 1500 come from?

1st owner purchased on 12/05/96 and owned in AK until 01/30/01 • 2nd owner purchased on 10/31/05 and owned in CA until 03/01/10 • 3rd owner purchased on 03/01/10 and owned in CA until 06/10/21. 1st owner drove an estimated 12,889 miles/year • 2nd owner drove an estimated 12,426 miles/year • 3rd owner drove an estimated 0 miles/year.

When was the last serviced Chevy C / K 1500?

Last serviced at 142,791 miles in Colorado Springs, CO on 02/20/21 • Vehicle serviced • Recommended maintenance performed • Oil and filter changed • Maintenance reminder reset • Drivability/performance checked • Fuel filter replaced. No accident or damage reported to CARFAX.

What causes a Chevy 350 to backfire constantly?

The air intake boot or tube transfers air from the mass air flow sensor into the throttle actuator and then into the engine. If there is a problem with these parts such as a tear or rip it will allow un-metered air into the engine which the computer will see via the oxygen sensor which in turn will deliver less fuel creating a lean condition.

What causes an intake back fire in an engine?

This will help locate the system that is having a problem and needs repair. An intake back-fire explosion can be caused by the fuel air mixture being to lean when the engine is demanding power. Every internal combustion engine runs on a mixture of 14 to 1 which is fourteen parts air to one part fuel.

What kind of engine does a Chevy k1500 have?

Your large and powerful Chevrolet K1500 is a formidable truck. Its engine is just as equal in might and impressiveness. Maintain its high performance with a new Chevrolet K1500 engine from AutoZone when your engine begins to give you trouble, like overheating and making knocking sounds. Use the form above to tell us what you drive.

Why does my C / K 1500 have no power?

I have a ’97 k1500 with a 350 and 4l60e automatic. Assuming all things are OK with the truck, would a bad fuel pressure regulator cause it to have no power at low rpm’s?

Why does my Chevy C / K 1500 bog out under acceleration?

It always bogs under acceleration, wont peel out even when its wet, and must downshift to gain speed on the highway (but it still runs at the normal rpm range when on the highway). 16 people found this helpful.

Where does white smoke come from on a Chevy C / K 1500?

White smoke comes from the exhaust all the time, it has hardly any power at all. It misses and backfires all the time. It stalls out alot when under a load, it was running great one day and then went to start it on a colder day.

Why does my Vortec truck won’t start?

How does a PassLock work on a 98 Chevy?

On the 98 the passlock is a module in the column and the key switch goes inside it. There is a contact inside this module that reacts to a change in magnetic field when the key switch is turned. There are three wires that come off the top of the module.

What kind of car is a 95 Chevy?

I have a 95 chevy 1500 4×4 5.7L 145,000mils. It’s been running good/bad for a few months. It will start right up and idle ok in park but as soon as I put it into drive it stalls out.

How many miles on my truck before the fuel pump went out?

Try crawling under the truck and whack the fuel tank with a rubber mallet while someone tries to start it. How many miles on The truck.. I have 4 chevies and each one The fuel pump went out between 90,000 -100,000.. I’ve had upwards of 120,000 before needing to replace mine in the 98 I had.

Why did my truck engine shut off going down the road?

That was because the top started to rust out, not from failure. When it went in my 98, I was out hunting and it died driving down the road. Replacing it on the truck wasn’t bad, I didn’t even attempt it on the Yukon. Try crawling under the truck and whack the fuel tank with a rubber mallet while someone tries to start it. Click to expand…

What kind of distributor wrench do I need for Chevy 1500?

To cut threw the case; just swap out your distributor but good luck finding a Distributor wrench that works really well. I in the end purchased a 9/16 Pontiac Distributor wrench then heated up the handle with a torch & bending it clock-wise about 90 degrees, it fits perfectly.

Ecm does not look at (reading on scanner will not change) unless engine is above 1000 rpm, Then you can adjust, either by rotating distributor while running (be careful)]

Is there a 97 5.7 Cam Vortec advance connector?

97 5.7L vortec, timing advance connector-forums, read that thread and see the issue, the explanation, the dealership advice, and the drawings are there to ponder. You do not need to buy expensive tools unless you use them constantly or want them for your individual pleasure. 31 people found this helpful. Thank-you for your answer.

Where is the cam sensor on a Vortec 350?

19 people found this helpful. The cam sensor is the “pick up coil” inside the distributor on a 350 vortec 96+ years. The only way to relearn or for better terms, set ignition timing, is using a scanner that reads camshaft retard degrees.

What is diagnostic code for 1998 Chevy k1500?

Here’s the diagnostic for P1345 (for a 1998 K1500) in case it is something else causing the code. So what you posted here says that if you can spin your distributer when its in the block something is wrong. I recently “timed” my truck when I did the intake manifold gasket.

Do you need scan tool for GM Vortec?

If you have a scan tool with the right capability, you can fine tune the advance for precision, but it’s not entirely necessary. Sweet!!! Thank you Sir. Essentially, nothing.

Where can I buy a Chevy k1500 oxygen sensor?

10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Whether you use your Chevrolet K1500 to transport your family or heavy supplies, it needs to maintain its reliability and performance . Keep your heavy hauler running smoothly with a Chevrolet K1500 oxygen sensor replacement from AutoZone to boost fuel economy and engine efficiency.

What to do if your Vortec won’t start?

96 Chevy C1500 5.7L Vortec Truck won’t start, Replaced Fuel Pump, Filter & Has Spark. Hey everyone, I have a 1996 Chevy C1500 with a 5.7L Vortec, I got the truck recently and was told it just needed a Fuel pump, I replaced the Fuel pump, and the Filter, also the pump turns on and there is fuel up at the rail, I pushed the pin and it shot right out.

Is the 1998 Chevy Silverado 5.7L hard to start?

Hello all, My 1998 chevy silverado 5.7L Vortec used to start as soon as you bump the key, and now it is hard to start (mainly when its cold) it takes several cranks of the engine to start and after truck warms up its okay, usually in the morning or if the truck sits for several hours after running. (i.e.

What’s the misfire code on a 1998 Vortec?

Can someone please help with what I should check next, I have a 1998 Chevy K1500 5.7 Vortec with a misfire, P0300 code for 3 months. runs a little rough, while driving under normal conditions it sputters, hesitates, and also will backfire, under heavy acceleration no noticeable skip, no sputters, and does not hesitate or backfire.

What kind of engine does a 1999 Chevy C / K have?

This 1999 Chevrolet C/K 2500 2dr HD Reg Cab 131.5 WB 4WD C6P 4×4 Truck features a 5.7L 8 CYLINDER 8cyl Gasoline engine. It is equipped with a 5 Speed Manual transmission. The vehicle is ORANGE with a Gray Vinyl interior.

Is the 98 Chevy 5.7 misfire running right?

I have a 98 chevy 1500 5.7. The truck doesnt run right at all. Msifres bad under acceleration. Idle ok when misses when reving and accelerating. I did a full tune up including plugs, wires, cap rotor and a new distributor. With key on i have about 60psi fuel pressure but idleing i only had 50psi.

Can a bad crank sensor cause a car to not start?

In other words, your GM vehicle will crank over when you turn the key to the Start position but will not start. Below is a simple list of more specific symptoms that accompany a bad crank sensor: The ignition coil will not spark. No spark from all of the spark plug wires.

What kind of engine does a 1997 Chevy k1500 have?

The C-series were the two-wheel-drive versions, while the K-series trucks were the four-wheel drive versions. The 1997 K1500 had many body and engine options available, so it was able to be built to suite different needs. The 1997 K1500 had four engine options available.

However, today, when the truck will crank and start, the antitheft icon goes off after a few seconds with the key on and stays off while the truck is running. It never flashed either today or yesterday though. And I don’t know if the antitheft system disables cranking or starting or both.

What’s the fuel pressure on a 1996 Chevy c1500?

I stuck a fuel pressure gauge on the fuel rail port and was reading about 50 psi. Unfortunately, as high as that sounds, the injectors won’t even open until you are at about 60 psi.

Is the Chevy Silverado 1500 a good truck?

The Chevrolet Silverado 1500 represents the status quo for a full-size light-duty truck. Its acceleration and braking performance are pretty average, while comfort and interior appointments are nothing special — at least not special enough to attract new buyers who currently own competing trucks.

What kind of engine does a Chevy Silverado 1500 have?

5.3L EcoTec3 V8 (L84) EQUIPPED WITH DYNAMIC FUEL MANAGEMENT 1 355 horsepower and 383 lb.-ft. of torque 2 8-speed automatic transmission (10-speed automatic transmission included on LT Trail Boss and High Country 4×4) 3 Auto stop/start technology 4 Standard on LT Trail Boss, LTZ and High Country; available on LT and RST

When did the fourth generation Chevy C / K come out?

For 1988, the fourth-generation C/K was introduced, including (nominal) 1⁄2 -ton, 3⁄4 -ton, and 1-ton pickup trucks and chassis cabs. In a nomenclature revision, GM adopted the 1500/2500/3500 payload series (previously used by GMC) for all full-size trucks (the Rounded-Line R/V series would do so for 1989).

What kind of engine does a C / K pickup truck have?

At its 1988 launch, the fourth-generation C/K pickup trucks shared its five-engine powertrain offering with the R/V series. On 1500 series vehicles, a 4.3 L Vortec V6 was standard, with the options of a 5.0 L V8, 5.7 L V8 and a 6.2 L diesel V8.

What kind of engine does a 1996 Chevy Z71 have?

SEE RECIPTS PICS FOR DETAILS. ENGINE RUNS GREAT TIMED AND TUNED UP. COOLING SYSTEM WAS FLUSHED AND I HAD A 2 ROW RADIATOR PUT IN INSTEAD FOR MORE COOLING CAPACITY!! HAS ELECTRONIC 4X4 PUSH THE BUTTON IN NEUTRAL AND 4X4 ENGAGES.

When did the Chevy C / K go out of production?

After the 2000 model year, the fourth-generation C/K was discontinued and was replaced by the GMT800 platform (introduced for 1999); heavy-duty chassis cabs remained in production through 2002. In line with the GMC Sierra, Chevrolet adopted a singular Chevrolet Silverado nameplate for its full-size truck line (which remains in use).

What kind of engine does a 1996 Chevy Silverado have?

1996 Chevy 2-door standard cab 350 V-8 automatic as stated before PARTS TRUCK engine runs fine drives down the road perfect but the transmission is blown it will need a different one interior is in good condition crack in windshield.

When does a 1995 Chevy K 1500 350 TBI hesitate?

An expert whose answer got voted for 100 times. Re: I have a 1995 chevy k 1500 350 tbi it hesitates when…

What’s the name of the Chevy C / K 1500?

Chevrolet C/K 1500 Questions – 97 chevy k1500 5.7 vortec is burning distributor cap and rotor about e… – CarGurus every month or two i am burning up distributor cap and rotor.

How to fix distributor on 97 Chevy k1500?

Just put a thin layer of silicone around the edge when replacing and boom problem fixed. Tried silicone, have replaced 5 times, just broke down again during rain storm. She just doesn’t like the rain. So putting in aluminum distributor will fix. Will see.

What are the specs of a 1997 Chevrolet C1500?

The table below shows all 1997 Chevrolet C1500 specs by style, including MPG (fuel economy), transmission details, and interior and exterior dimensions. Additionally, find 1997 Chevrolet C1500 warranty and reliability information, such as limits on bumper-to-bumper coverage and major components.

What kind of engine did Chevy have in 1997?

Chevy placed a vortex or mini tornado within the combustion chamber to efficiently blend gas and air together. Vortec engines are the base engine used in all Chevy cars and trucks and come in a variety of horsepower and torque ratings. During 1997 Chevy still had a big block engine, the 454 cubic inch.

What was the horsepower of a 1997 Vortec truck?

The truck engine was rated at 255 horsepower and 330 foot-pounds of torque. The 5700 engine appeared in the 1997 Chevrolet Express, Chevrolet Suburban, Chevrolet Tahoe, Chevrolet/GMC full-size trucks and the Cadillac Escalade. This engine was replaced in 2002 by the 5.3 5300.

What kind of engine was in a 1997 Chevy Tahoe?

The 5700 engine appeared in the 1997 Chevrolet Express, Chevrolet Suburban, Chevrolet Tahoe, Chevrolet/GMC full-size trucks and the Cadillac Escalade. This engine was replaced in 2002 by the 5.3 5300. The premier Vortex engine during 1997 was the 4300 or 4.3 L V-6 90-degree engine that replaced the Chevrolet 250 in all light truck applications.

When did my Chevy C / K 1500 engine stall?

Piece of cake……The big important one was – Bulletin #020604052 Date:Oct. 2002 Summary: Engine Stall, No Start, Hard Start Cond. CNHTSA Item #00000167 (not sure what this is). 8 people found this helpful. Still not much luck on this end…..I did repair some wires at the O2 sensor and also at the knock sensor.

Is the 1998 K 1500 hard to start?

Not open for further replies. i am working on a 1998 k 1500 5.7 the truck is very hard to start but when it does it runs fine.. good power and will start fine afterwards,,the problem i am having is when it sits for 2 days then once again it is very hard to start…

Are there any problems with the Chevy 4.3 engine?

Once you have ruled out all the basics, you can go back to what the Chevy 4.3 engine is known for: bad idle air control valves and throttle control switches. This article was written by a professional writer, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

How long does a Chevy 4.3L Vortec engine last?

3 vortec is a very strong and reliable motor, proven by it being the longest lasting production vortec engine. Generally, these engines are extremely capable of lasting up to 300,000 miles.

Why is my Chevy Vortec 4300 V6 leaking fuel?

In the L35 and LF6 engines, the spider injectors are known to leak at the pressure regulator and at the supply and return lines due to a design fault. Outside of leaking fuel onto the exterior of the engine itself, it can cause excess fuel to get sucked into the engine.

Can a Chevy C / K 1500 engine not start?

Chevrolet C/K 1500 Questions – truck will not start, engine turns, but does not fire at all. – CarGurus truck will not start, engine turns, but does not fire at all. other computer-related things that could be interfering?

Why is my Chevy 305 not running properly?

The stock headers further restricted air intake because of pollution concerns, though replacement Edlebrock or Vortec headers increase airflow while still maintaining proper emissions. Upgrade the air filter assembly with a modern unit to let the engine “breathe” more easily on the intake.

What should I do about my Chevy 305 engine?

The cam drive gear is of special concern on 305 engines. 305s manufactured before 1988 used a nylon-toothed cam gear to reduce noise. This gear is prone to failure and should be replaced with a solid steel gear. If replacing the stock water pump consider an electric version to reduce the workload of the engine.

Why is my a / C not cold in my Chevy Silverado?

If the system was completely empty (no pressure at all) the A/C compressor would not engage to prevent damage to the system. However, there’s often enough pressure left in the system to engage the compressor for short periods of time, while not enough to cool the air.

Why does my GMC pickup truck use so much oil?

The AFM system, which disables some of the engine’s cylinders at lower RPMs to reduce fuel use, is the most common cause of this issue. While the system accomplishes this, it also leads to oil use problems. Some drivers have reported using as much as a quart of oil every 1,000 miles.

How often should I change the oil in my Chevy truck?

While the system accomplishes this, it also leads to oil use problems. Some drivers have reported using as much as a quart of oil every 1,000 miles. You’re most likely to start noticing excessive oil use around the 60,000-mile mark. To help avoid problems, change your oil regularly.

What causes the headlight switch on a Chevy Silverado to fail?

Share it! The headlight switch used on the Chevrolet Silverado 1500HD and 2500HD is known to fail through normal operation. Since the headlight switch is also integrated into the interior lights, a malfunctioning switch can cause issues with interior lights as well. Symptoms of a failed headlight switch include:

Why does my car not start when I turn the key?

A low or bad battery can be easily tested with a standard ohm meter or at any auto repair shop or parts store (they usually do this free of charge). A loose battery cable connection is often the simplest of causes for a non-start. A bad starter solenoid means replacement is needed.

Why are the dashboard lights on my Chevy not working?

If the dashboard lights in your Chevy are dim, chances are you can fix it yourself. If it’s light out, make sure that the headlights aren’t turned on. Many headlights often dim the dash automatically when they’re switched on, so this might be the cause of the problem. If that’s not it, look for the dimmer switch.

What are the warning lights on a Chevrolet?

The following are warning lights and indicators found in vehicles built by Chevrolet. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray). There are nearly 50 of them so search carefully!

What causes engine to crank for long time before it starts?

When an engine cranks for a long time before it starts, either spark or fuel is missing or weak and each has its own reasons. Most of the time, the air / fuel mixture has been disturbed and there is too much air or not enough fuel.

What kind of Chevy truck won’t start?

In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start…. In this video we encounter a condition where a 2002 Chevy Silverado ( Similar to GMC Sierra ) pickup has a symptom of the engine cranks over but won’t start….

When was the GMC C / K HVAC unit last used?

This Heater AC Control Unit was used on the 1996-98 line of Chevrolet and GMC C/K Pickups, and on 1996-99 GM Suburbans, Tahoes, and Yukons. It was no longer used after 1999, due partly to unreliability, and partly due to upgrades to newer technology.

What is the temperature control on a GMC CK truck?

Power is routed back out to Pin 7 through a 3.8 ohm resistor and the Max AC switch, but on a 1500 truck Pin 7 is not used. The Blend (temperature) door control is powered directly from +12V via Pin 5.

How do you test a / C on a GMC CK truck?

TESTING LOW PRESSURE SWITCH. With the truck running, A/C turned on. Check the Dark Blue wire at the low pressure switch for +V with the switch Disconnected. Check for ground on the black wire. With the switch plugged in BOTH wires should show ground.

How long does it take to replace a starter and solenoid?

Yeah, it really should not take more than 30 minutes, even for your first attempt. Reomve the three wires from the solenoid, but mark them or remember which wire went where…this is critical! Remove the three 9/16″ bolts that hold the starter to the trans, and let it down easily.

Can You Drop a starter without dropping the solenoid?

No not really. You usually only have two bolts to remove to drop the starter and two more to disconnect the solenoid. Reassemble in reverse. I am including a link to some videos that may help you. Ralph http://www.youtube.com/watch?v=WImZRSAed… Disconnect the battery before working on the starter. Ralph Was this answer helpful?

When to change the starter on a c1500?

Changing your Chevy C1500 starter motor promptly after the first signs of shortage helps to avoid costly repairs or services. A quality replacement starter utilizes a 12-volt battery source to start the engine and it should rotate the engine between 85 to 150 RPMs.

Can you replace the starter on a Chevy truck?

Here is how to replace the starter motor on a Chevrolet truck with a 5.7 L 350 V8 engine. Replacing the starter on a Chevrolet truck is an easy job, as it is only held in place with 2 Bolts, and they are very easy to get to. In this video you can watch me show you how to replace a starter on your Chevrolet truck.

How long does it take to replace the starter on an 87 S10?

I have done this job on an 87 S10 with 2.8 litre engine and automatic transmission. In a perfect world, replacing the starter could be done in about 30 minutes, but if you run ito the same complications that I did, and wish to avoid any disasterous consequences, be prepared to spend an hour or two.

What happens if you replace starter and solenoid cable?

New $5 cable and it starts, amps are solid at 14.5ish starter turns over and everything is great. The cables on this model (mine is a 1988 Chevrolet K2500 5.7L) for the negative lead to the block can burn out and it will not show any ware or burning. The cable just fries internally and has a slight or no connection at all.

What kind of engine does Chevy C / K 1500 have?

For 1997, the optional third door could be ordered on any C/K 1500 model, not just the top-line Silverado. Chevrolet made few changes to the C/K as it readied a replacement for the 1999 model year. At introduction, base engine for the C/K 1500 and 2500 was a 160-horsepower, 4.3-liter V6.

What kind of engine was in 1990 Chevy C / K?

The 7.4-liter V8 engine was revised, and could be mated to a 4-speed automatic instead of the prior 3-speed. In the 454 SS, that engine now made 255 horsepower–25 more than in 1990. 1992 C/K Pickup. Sportside trucks with the flare-fendered cargo box could have an extended cab this year.

What kind of car is a 1999 Chevy Suburban?

Topaz Firemist Metallic 1999 Chevrolet Suburban 1500 4WD 4-Speed Automatic Vortec 5.7L V8 SFI Laramie GM Auto Center offers One Low Price, Plain Simple-Always! Customers have told us that the most unpleasant aspect of buying a vehicle is negotiating the price. We’ve decided to give EVERYONE our BEST PRICE right up front.

Chevrolet C/K 1500 Questions – 98z71 5.7 multiple misfire P0300 fouling 1 3 5 7 plugs with gas what c… – CarGurus only on that side… try and go up 2 heat ranges on that side,,,and / or first .. take some good pictures of those plugs and post them…

How much torque does a C / K 1500 have?

Check for vacuum leaks, that is a Vortec engine, intakes are prone to leak, check the bolts, there are only 8 of them, torque to 15 to 20 ft.lbs. They say 12 ft.lbs. but that is pretty light.

Can a 1997 Chevy c1500 5.7L start?

1997 Chevy C1500, 2WD, 5.7L won’t start – cranks fine. No codes – good fuel pressure ( 60+ psi – new pump), good spark, 1997 Chevy C1500, 2WD, 5.7L wont start – cranks fine. No… It will not start. I changed the fuel filter and fuel pump It will not start.

Is the Chevy c1500 a two wheel drive truck?

I have a 1993 Chevy C1500, two wheel drive, overdrive trans. It will not take off with truck in drive but if i shift to second i can pull off and than manually shift two d … read more

Why is my 5.3 liter Chevy engine not working?

There is also the factor of environmental pollution which is also related to excessive oil usage. When you factor in excessive oil usage, the greenhouse gas increases rapidly, which then leads to pollution. Unfortunately, for many 5.3 Liter Chevy Engine owners, the cost to address this problem is too high in terms of labor and parts.

Can a Chevy Silverado 1500 start and run?

Although I tried to start it multiple times over a couple weeks I gave it one last try after I called the tow truck. It started right up and engine stayed running like it was supposed to. No more problems for almost a year until about a week ago. I did nothin to fix it a year ago.

Can a 5.3 liter Chevy engine be rebuilt?

Unfortunately, for many 5.3 Liter Chevy Engine owners, the cost to address this problem is too high in terms of labor and parts. Once the owner takes into account the engine rebuilding process, the engine owner runs the risk of a poorly rebuilt engine and even allocating piston rings and gaskets.

Why does my Vortec 5300 engine not start?

A faulty fuel pressure regulator can lead to your truck either getting too much fuel, or too little fuel. The result in both instances can be misfires, poor idling, loss of power, engine shakes during acceleration, and more. On the Vortec 5300, one of the most common symptoms is hard starting, or trouble starting the car.

Why does my GMC Suburban not start up?

It shoued DTC 15 open circuit in coolant temp sensor, 22 something about the throttle position sensor and 54 which is fuel pump circuit low voltage. BTW, I found out the truck will start if I keep the gas pedal to the floor when cranking, however the engine just dies as soon as I let off the pedal.

What is signal wire on GMC Suburban 5.7?

The signal wire goes from 0.51 volts at an idle to 4.56 volts at wide open throttle. Oil pressure sensor tan middle wire shows a good ground. Grey wire show 8.75 volts and the red wire shows 12.37 volts. If I jump the two end wires together the fuel pump runs constantly however, this time is wont start.

Why does my 1990 Chevy Silverado not start?

My 90 would not start if the vacuum line to the MAP sensor was disconnected. The MAP is located behind the TBI. Be sure the vacuum hose is in good shape. Mine has to be replaced as the glue no longer worked and it leaked. If you have a vacuum pump, make sure the MAP can hold a vacuum or it needs to be replaced.

Can a 1999 Chevy c1500 / k1500 start?